hilum

Set up your bench

Photograph seeds so the measurement comes out right.

Scanner or camera, ruler, background and light. Four choices decide whether the measured outline is the seed's or its shadow's.

Simulation · flatbed scanner and APS-C camera with a 50 mm lens

Scale

A ruler in every image

The DPI saved in the file is a declaration. A ruler photographed in the same plane as the seeds is a measurement. In a scan from the orchid research group (GPEOrq), 10 mm of the ruler cover 1,906 pixels: each pixel is 5.25 µm, and SeedCounter converts every seed to millimeters.

Scanner and camera both measure well. The scanner gives more pixels per millimeter over a small area. The camera captures the whole plate in one shot and takes extension tubes when detail matters, as with the embryo.

Light

Between 35° and 65°, with a diffuser

Raking light casts a long shadow: on a seed 1.4 mm tall, the shadow runs past 2 mm and touches its neighbor. Overhead light causes glare on the seed coat. In the middle range, with a diffuser, the outline stays clean.

shadow = height ÷ tan(elevation)

Rules

Eight rules for the plate

They apply to both scanner and camera. Each one prevents an error that would show up later, in the measurement.

  • Scale

    Ruler in the plane of the seeds

    A millimeter ruler at the same height as the seeds, inside the frame, in every image.

  • Background

    Contrast with the seed

    A matte background in a color opposite to the seed's. Blue paper works well with yellowish seeds.

  • Color

    Gray card in the corner

    A neutral gray card in the scene lets you correct the white balance and compare color across photos, which matters in the tetrazolium test.

  • Light

    Two sides, with a diffuser

    Panels on opposite sides, between 35° and 65°, balance the shadow. Avoid direct light from a window.

  • Plate

    Seeds not touching

    Leave a gap between seeds. The app splits touching seeds with a cut that you approve, but every cut is one more thing to check.

  • Camera

    Everything on manual

    Low ISO, f/8, manual focus at the height of the seeds, and a shutter release from the computer or a remote, so the camera doesn't shake.

  • Scanner

    Don't press the lid

    Don't crush the seeds with the lid: cover them with a black box instead. Turn off sharpening and automatic corrections.

  • File

    No compression

    Save as TIFF or PNG. JPEG creates artifacts right at the edge, where the outline is measured.

Before you load

Five checks on the spot

Checking the photo while the sample is still on the bench takes a minute. Redoing it later costs you the sample.

  1. FocusThe seed edge is sharp at 100% zoom.
    100% zoom
  2. Blown highlightsNo seed looks flat white, without texture.
    histogram
  3. Pixels per seedThe seed's shortest axis spans tens of pixels. At 30 px, one pixel of error at the edge is already 3%.
    30 px · 3% per px
  4. TouchingFew seeds touching. If many are, spread them out before you shoot.
    visible gap
  5. Even lightThe corners of the plate are as bright as the center.
    corners × center

On a real bench

The same rule, on film

Every animation on this page gets a filmed version, shot at a home station with an ordinary camera, scanner and desk lamp.

The same plate lit from a low angle, at 45° and overheadF04 · recording script
Real footage coming soon · F04to be filmed: the shadow changing with the height of the light
Setting up the bench layout from scratch, in one minuteF06 · recording script
Real footage coming soon · F06to be filmed: camera on the arm, ruler, gray card and light

3D simulator

Plan your bench before you buy the first piece

Eight scenes with the measurements of a real layout: camera height and field of view, lenses and tubes, light and shadow, depth of field, CIS × CCD scanners and the virtual ruler. Rotate, zoom in and change the settings.

Open the 3D simulator Works best on a computer. On a phone, use two fingers to rotate and zoom.

Photo ready? Now count.

Load the image into SeedCounter, mark the ruler and check the seeds.

Open SeedCounter